Strata CIX 200 Programming Manual Download Page 334

Page: 334 / 508

IP Telephone Programming

IP Telephone Installation and Network Connection Setup

8-20

Strata CIX Programming Vol.1 12/09

Figure 8-1 Station IP NAT Example

16 IP NAT/No Peer to Peer

Enable if the IP telephone is in a NAT (Network Address Translation)
environment.

Possible values:Enable or Disable (Default)

Refer to Figure 8-1.

17 Base UDP Port for IP

Telephone Media
Channel

The base UDP port for the IP telephone media channel can be set to
accommodate a particular network configuration.

Possible values:1026 ~ 65532 (Default = 49154)

Note

Only even port numbers can be assigned.

IELD

ESCRIPTION

CIX

When a system has LIPUs with private IP addresses and LIPUs with public IP addresses set

IPT (2)

Global Network

LIPU (2)

LIPU (1)

Public IP Address

Private

NAT

Router

Private IP

Address

IP Address

IPT (1)

Private IP

Address

Prog. 250 - FK16 as shown here to prevent one way speech path between IPT (1) and IPT (2).

Prog 250-FK16 = Disabled for IPTs on this LIPU (Peer-to-peer mode)

Prog 250-FK16 = Enabled for IPTs on this LIPU (no peer-to-peer)

If the NAT router is a inconsistent/symmetric type, the IPTs
on LIPU (1) should have Prog 250-FK16 set to Enabled.

NAT

Router

NOTE

Gateway

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands

Strata CIX 200, Programming Manual

Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands