Strata CIX 200 Programming Manual Download Page 413 | Manualshive

Page: 413 / 508

background image

Operation

System Setup

Strata CIX Programming Vol.1 12/09

10-9

Oper

ation

It should be noted that the Network eManager screen will ‘freeze’ while modem updates are in progress.
This freeze, when using a dial-up modem connection, can last up to 60 minutes. You can check the status
of the file transfer when using a dial-up modem by right clicking on the connection icon that appears in the
tool tray at the bottom of the screen. (The Remote Update file size is about 9MB). Over a LAN connection
remote update takes approximately 15 seconds.

CAUTION! When updating a CIX200 R3 system with the existing LCTU1A card to R4, it will be

necessary to perform the update locally (remote update will not work). After the
system has been updated to R4 the Remote Update function will be available.

System Turn-on and Start-up Time

When a Release 4 system is turned on it takes about 30-90 seconds to operate. CIX Release 2.x and 3.x
take about 15 seconds.

910 Data Backup

Prerequisite Program:

908

This program enables you to backup programmed data from Strata CIX to an SM/SD Card.

1. Install the SM/SD Card into the designated slot of the Strata CIX processor.

Note

The SM/SD card must be formatted by Strata CIX and the “Progdata” folder must be empty (no
Default.dat file)

2. Select Maintenance > Data Backup.

3. Select the system(s) to backup. Click

Cancel

to interrupt the selected function.

4. Click

Backup

.

5. The Progress field displays the progress of the selected function.

F

IELD

D

ESCRIPTION

Backup

Select one of the following buttons. When performing a Backup, you must use
a formatted SM/SD card.

•

Backup – Backup Strata CIX data to SM/SD card. This creates a Default.dat
file under the Progdata folder of the SM/SD card.

Notes

•

Default.dat is the name of the file that is created and it contains all Strata
CIX programmed data. It is not default data. It is data that is currently
programmed in the Strata CIX.

•

The Progdata folder on the SM/SD card must be empty before trying to
backup data. You can use FTP to copy and delete an existing default.dat
file.

•

Cancel – Cancel the Backup/Restore function.

Completion

Current Status of Backup.

Possible values:Completed successfully, Not completed.

«
...
411
412
413
414
415
...
»

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Brand: Olympia Pages: 54

Brand: Hanlong Pages: 57

Brand: JabloCom Pages: 16

Brand: Samsung Pages: 24

Brand: Yealink Pages: 64

One Touch 997D Ultra

Brand: Alcatel Pages: 21

Brand: Allview Pages: 142

Brand: M4 Pages: 22

Brand: ZTE-G Pages: 51

Brand: Archos Pages: 40

Brand: Sony Ericsson Pages: 30

Brand: TCL Pages: 19

Brand: TCL Pages: 10

BLACKVIEW GBV7000 Pro

Brand: Iget Pages: 47

Brand: UMIDIGI Pages: 40

Brand: AMGOO Pages: 44

PHONEEASY 410S gsm

Brand: Doro Pages: 140

Brand: Alcatel Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands