Strata CIX 200 Programming Manual Download Page 427 | Manualshive

Page: 427 / 508

background image

Strata CIX Programming Vol.1 12/09

11-1

Ma

in

te

n

a

nc
e

Maintenance

11

This chapter discusses Strata CIX maintenance functions.

Trace Function

To analyze Strata CIX problems efficiently, Toshiba needs to get the event trace data and ISDN trace data.
These data sets enable analysis of the problems Strata CIX may experience. It is helpful for
troubleshooting problems that are difficult to duplicate.

Please contact Toshiba Technical Support to coordinate the running of the procedures that appear in this
section. Technical Support will walk you through the required steps.

Trace Data

By running traces when tests are conducted on your Strata CIX system, you ensure that data are being
kept in the event your system encounters a problem. This data can be sent to Toshiba Tech Support for
analysis and troubleshooting.

Strata CIX can collect the following trace data:

•

Error Log (including crash dump)

•

Event Trace

•

ISDN L3 trace

Error Log

When Strata CIX detects an error the information is stored automatically without executing a program.
However, if the system locks up, you must restart the system to save the data to the Secure Digital (SD) or
SmartMedia (SM) card.

Start/Stop/Store Trace Data

When you execute a test, start recording the trace data by enabling the

Event Trace Control

(Program

903).

. If you use ISDN extensions or trunks, please record ISDN trace data by starting

ISDN Trace Location”

To test and retrieve trace data

Note

This procedure requires use of optional SD/SM reading hardware and software or FTP management
with a personal computer. See

“908 Secure Digital and SmartMedia”

1. Start your test. If a problem occurs, stop the trace (please refer to the

Event Trace Control

ISDN Trace Location

program instructions in this manual).

2. Verify the results by running the same test(s) again. If the problem can be duplicated the information

contained in the trace data becomes more useful.

3. Unmount data to the SD/SM using

“Set Time and Date”

«
...
425
426
427
428
429
...
»

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Brand: Samsung Pages: 35

Brand: Samsung Pages: 7

Brand: Samsung Pages: 40

Brand: Samsung Pages: 16

Brand: Samsung Pages: 17

Admire SCH-R720

Brand: Samsung Pages: 136

A840 - SPH Cell Phone

Brand: Samsung Pages: 146

A727 - SGH Cell Phone 28 MB

Brand: Samsung Pages: 185

A660 - SPH Cell Phone

Brand: Samsung Pages: 9

A517 - SGH Cell Phone

Brand: Samsung Pages: 163

A436 - SGH Cell Phone 3 MB

Brand: Samsung Pages: 126

A437 - SGH Cell Phone

Brand: Samsung Pages: 120

A310 - SCH Cell Phone

Brand: Samsung Pages: 6

A117 - SGH Cell Phone

Brand: Samsung Pages: 92

A127 - SGH Cell Phone

Brand: Samsung Pages: 123

Byline SCH-R310 Serie

Brand: Samsung Pages: 120

Brand: i.safe MOBILE Pages: 49

Brand: i.safe MOBILE Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands