Strata CIX 200 Programming Manual Download Page 447

Page: 447 / 508

Telephone Button Programming

900 Series Programs

Strata CIX Programming Vol.1 12/09

13-13

lepho

ne Butt

Progra

mming

1. Press

FB01

to enter parameter. Enter

1~4

as your command choice. Press the

Scroll

Page

button

to make your selection.

2. Press

Hold

to confirm and

Hold

again to execute.

3. Wait for the PROG= prompt to appear before proceeding.

4. Enter another program number to continue programming or press

# # Hold

again to exit programming

mode.

Strata CIX Secure Digital/SmartMedia Directories

Running the Normal and Forced options of this program creates five directories on the SmartMedia card as
follows:

•

Admlog

– The Admlog folder saves

•

Errlog

– System error logs are saved into this folder.

•

Evnttrce

– Strata CIX eManager Event Trace files are saved into this folder.

•

Progdata

– Your Strata CIX programmed settings are all saved in this folder.

•

Program

– The operating software and default data of the Strata CIX is saved in this folder.

When a backup is performed, Strata CIX saves programmed data to the

Progdata

folder.

MAC Address (System Serial Number)

This program enables you to display your CIX1200 or CIX670 System Serial Number.

Program Number(s): 909

Prerequisite Program:

None

Reference:

None

Access Sequence:

Hold Q#Q#1Q2Q3Q.

At the

PASSWORD

= prompt enter your password and press

Hold

At the

PROG

= prompt enter

909

and press

Hold

FB Name

Summary

Value

LCD Prompt

Control

Choose SmartMedia card formatting method:

Normal

– creates any Strata CIX SmartMedia directory

that does not exist already. Exiting directories are not
overwritten by this procedure.

Forced

– erases any existing directories and files. All

existing data is overwritten. See

Strata CIX Secure Digital/

SmartMedia Directories

below for more information.

Unmount

– writes data into SmartMedia Card. Always run

unmount before removing the SmartMedia card to prevent
damage to the card.

Transfer

– writes data from static RAM to SmartMedia

Card.

1:Normal

2:Forced

3:Unmount

4:Transfer

1:NORMAL

2:FORCED

3:UNMOUNT

4:TRANSFER

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands

Strata CIX 200, Programming Manual

Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands