Strata CIX 200 Programming Manual Download Page 301

Page: 301 / 508

Trunks

Trunk DID/DNIS Setup Wizard

Strata CIX Programming Vol.1 12/09

6-47

runks

325 Strata Net Full IP Trunk Assignment

Prerequisite Program:

100

page 4-1

; 304 on

page 6-1

; 306 on

page 6-5

This command assigns Strata Net IP trunks.

1. Select Trunk> Full IP Strata Net.

2. Setup the Channel Group by adding values to the remaining fields.

3. Click

Submit

IELD

ESCRIPTION

Channel Group

Enter a channel group number.

Possible values:1~32 (CIX40), 1~32 (CTX100), 1~48 (CTX670 Basic &

CIX200), 1~128 (CTX670 Exp), 1~ 48 (CIX1200 HCTU only),
1~128 (CIX1200 HCTU+HEXAU), 1~220 (CIX1200 HCTU
+HEXBU)

01 Equipment

Assign the Equipment Number of the LIPU/LIPS MIPU and/or GIPx card.

CIX40 GIPx/MIPU card in R1 CHSU40A Cabinet is 01/Slot 06 (0106).

CIX40 GIPx/MIPU card in R2 CHSU40A2 Cabinet is 01/Slot 05 (0105).

Cabinet numbers:

•

CIX100: Select 01 for Base and Expansion cabinet.

•

CIX670: Select 01 for Base and 02 ~ 07 respectively for each
Expansion cabinet.

•

CIX200: Select 01 for Base and 02 for Expansion cabinet.

•

CIX1200: Select 01 for Base and 02 ~ 12 respectively for each
Expansion cabinet.

Slot numbers:

•

CIX100: Select 01 or 03 for Base slots and 05 or 07 for Expansion
slots

•

CIX200: Select 01 ~ 04 for either cabinet.

•

CIX670: Select 01, 03, 05 and 07 for Base slots and 01, 03 and 05
for Expansion slots.

•

CIX1200: Select 01, 03, 05 and 07 for Base slots and 01, 03 and
05 for Expansion slots.

02 LAN Interface Number

Select “1” for an LIPU or “2” for an LIPS. Not used for MIPU/GIPU.

Possible values:1 or 2

03 SIP IP Channels

Enter the number of GIPU, MIPU, LIPU or LIPS channels to be assigned as
Strata Net IP resources

Possible values:(GIPU) 1 ~ 8, (MIPU16, LIPU, LIPS) 1 ~ 16, (MIPU24) 1 ~ 32

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands

Strata CIX 200, Programming Manual

Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands