manualshive.com logo in svg

Strata CIX 200, Programming Manual

The "Strata CIX 200" General Description Manual is a comprehensive guide for users of this advanced telecommunication system. This manual provides in-depth information about its features, functions, and troubleshooting, enabling users to maximize the potential of their device. Download this manual for free from our website and become an expert user of Strata CIX 200. [Website]

Share
Download
background image

Trunks

Trunk DID/DNIS Setup Wizard

6-52

Strata CIX Programming Vol.1    12/09

24 TOS Field Type for 

Media

Not supported in this release - see Prog 150. MIPU global settings are used. If 
field 23 Diffserv is enabled, select DSCP (Differentiated Services Code Point 
format) or TOS (Type Of Service format). If TOS is selected, set the packet 
priority level in field 25 TOS Precedence Type for Media; if DSCP is selected, 
set the packet priority level in field 26 DSCP for Media.

Possible values:TOS or DSCP (Default)

25 TOS Precedence Type 

for Media

Not supported in this release - see Prog 150. If TOS is selected in TB24 TOS 
Field Type for Media, select a packet priority level - where Critical/ESP provides 
the highest and Routine provides the lowest priority. If TOS is selected in field 
24, make selections in TOS Delay, TOS Throughput Delay, and TOS Reliability 
Type.

Possible values:Routine, Priority, Immediate, Flash, Flash Overd, or Critical/

ESP (Default)

TOS Delay Type for Media

Not supported in this release - see Prog 150. If TOS is selected in field 24 TOS 
Field Type for Media, select 'Normal' for most cases

Possible values:Normal (Default) or Low

TOS Throughput Type for 
Media

Not supported in this release - see Prog 150. If TOS is selected in field 24 TOS 
Field Type for Media, select 'Normal' for most cases

Possible values:Normal (Default) or High

TOS Reliability Type for 
Media

Not supported in this release - see Prog 150. If TOS is selected in field 24 TOS 
Field Type for Media, select 'Normal' for most cases

Possible values:Normal (Default) or High

26 DSCP for Media

Not supported in this release - see Prog 150. If DSCP is selected in field 24 TOS 
Field Type for Media, select a priority level

Possible values:0 ~ 63 (Default = 0)

27 Diffserv for Signaling

Not supported in this release - see Prog 150. Enable Diffserv (Differentiated 
Services) priority control if voice packets on an IP (internal) Network should be 
prioritized with priority tagging. Higher priority, time-critical BIPU/IPT voice traffic 
can have preferential treatment when other traffic is running at best effort. If 
Diffserv is enabled you must set field 28 TOS Field Type for Signaling as DSCP 
or TOS.

Note

Diffserv is usually not a standard feature with most ISPs; contact your 
ISP to make arrangements to provide Diffserv or this feature will not 
work correctly.

Possible values:Enable or Disable (Default)

28 TOS Field Type for 

Signaling

Not supported in this release - see Prog 150. If field 27 Diffserv for Signaling is 
enabled, select DSCP (Differentiated Services Code Point Format) or TOS 
(Type Of Service format). If TOS is selected, set the packet priority level in field 
25 TOS Precedence Type for Media. If DSCP is selected, set the packet priority 
level in field 26 DSCP for Media.

Possible values:TOS or DSCP (Default)

F

IELD

D

ESCRIPTION

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

NEC ML440 Manual preview
ML440
Brand: NEC Pages: 7
NEC UX5000 Easy Setup Manual preview
UX5000
Brand: NEC Pages: 68
NEC UNIVERGE MH240 Setup Manual preview
UNIVERGE MH240
Brand: NEC Pages: 44
Wiko lubi 3 User Manual preview
lubi 3
Brand: Wiko Pages: 56
Hanlong UC802(P) User Manual preview
UC802(P)
Brand: Hanlong Pages: 60
AEI COMMUNICATIONS SFT-1200 Quick Installation Manual preview
SFT-1200
Brand: AEI COMMUNICATIONS Pages: 5
ZTE-G R237m User Manual preview
R237m
Brand: ZTE-G Pages: 51
Audiovox BAM-101 User Manual preview
BAM-101
Brand: Audiovox Pages: 39
Sagem MYX5-2V User Manual preview
MYX5-2V
Brand: Sagem Pages: 92
Talk To Me Technologies wego A-PLUS Series User Manual preview
wego A-PLUS Series
Brand: Talk To Me Technologies Pages: 28
Sony Ericsson Xperia X10 Extended User Manual preview
Xperia X10
Brand: Sony Ericsson Pages: 113
ShoreTel IP-480 User Manual preview
IP-480
Brand: ShoreTel Pages: 2
Polycom VVX 501 Series User Manual preview
VVX 501 Series
Brand: Polycom Pages: 2
Zte Prelude Quick Start Manual preview
Prelude
Brand: Zte Pages: 24
Xiaomi Redmi 3 User Manual preview
Redmi 3
Brand: Xiaomi Pages: 2
Acer P400 User Manual preview
P400
Brand: Acer Pages: 91
Acer P300 User Manual preview
P300
Brand: Acer Pages: 96
Acer V370 User Manual preview
V370
Brand: Acer Pages: 51

Brands by name

Popular brands

Load more brands