Strata CIX 200 Programming Manual Download Page 324 | Manualshive

Page: 324 / 508

background image

IP Telephone Programming

IP Telephone Installation and Network Connection Setup

8-10

Strata CIX Programming Vol.1 12/09

151 BIPU Configuration

This program is used to set up the IP address of the specific BIPU card to support the IP-Telephone. BIPU
card must be assigned before configuring the specific BIPU card.

1. Select IP-Telephony > BIPU Configuration.

2. Enter Program 151 data.

3. Click

Submit

.

Note

Refer to Program 161 - IP-Telephony > L/M/G IPU Configuration.

F

IELD

D

ESCRIPTION

Cabinet & Slot Number

Enter the cabinet and slot number of the BIPU to be configured.

Note

: BIPU cards must first be installed using PRG100 - System\Card

Assignment.

BIPU cards can be installed in the slots listed:

Cabinet

•

CIX/CTX100: Select 01 for Base and Expansion cabinet.

•

CIX200: Select 01 for Base and 02 for Expansion cabinet.

•

CIX/CTX670: Select 01 for Base and 02~07 respectively for each
Expansion cabinet.

•

CIX1200: Select 01 for Base and 02~12 respectively for each
Expansion cabinet.

Slot numbers:

•

CIX/CTX100: Select 01~04 for Base slots and 05~09 for Expansion
slots.

•

CIX/CTX100: Virtual Slot for ACTU Relay = Cabinet 02, Slot 05.

•

CIX200: Select 01~04 for either cabinet.

•

CIX/CTX670: Select 01~08 for Base slots and 01~10 for Expansion
slots.

•

CXI1200:Select 01~08 for Base slots and 01~10 for Expansion slots.

01 IP Address

Enter the BIPU IP Address.

02 Subnet Address

Enter the Subnet Address of the BIPU.

03 Default Gateway

Address

Enter the Default Gateway Address of the BIPU card.

04 Version Number of

BIPU

This is a read-only field. The version number will automatically appear when the
card is configured correctly.

05 IP Strata Net RTP Base

Port (BIPU)

The base of the 32-port range which can be used by BIPU card to assign port
numbers for the IP Strata Net RTP protocol.

Possible values:16384~65504 (default = 20992). Only even numbers can be

assigned.

«
...
322
323
324
325
326
...
»

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Brand: Samsung Pages: 114

Brand: Samsung Pages: 8

SCH-a610 Series

Brand: Samsung Pages: 12

Brand: Samsung Pages: 28

Brand: Samsung Pages: 28

Brand: Samsung Pages: 35

Brand: NEC Pages: 216

Brand: Samsung Pages: 135

Brand: Mitsubishi Pages: 72

Brand: Opel mobile Pages: 76

Brand: Rath Pages: 9

Brand: Mobeye Pages: 28

Brand: Zonda Pages: 27

Brand: T-Mobile Pages: 258

Brand: HTC Pages: 310

Brand: Proolin VoIP Tech Pages: 25

Brand: Beacon Pages: 2

Brand: Alcatel Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands