Strata CIX 200 Programming Manual Download Page 248

Page: 248 / 508

Station

Assignment

5-44

Strata CIX Programming Vol.1 12/09

16 B Channel Selection

Select originating B Channel method.

Possible values:

•

Exclusive – (default) Channel is indicated and no alternative is acceptable.

•

Preferred – Channel is indicated and any alternative is acceptable.

•

Any Channel – Channel is indicated and any channel is acceptable.

17 Idle B Channel

Selection

Choose Idle B Channel selection method.

Possible values:Forward Cyclic, Backward Cyclic, Forward Terminal or Backward

Terminal (default)

•

Select Forward Cyclic (from lowest to highest number of B-channel).

•

Select Backward Cyclic (from highest to lowest number of B-channel).

•

Select Forward Terminal for the lowest number B-channel (The Low-Low B-
channel selection).

•

Select Backward Terminal for the highest number B-channel. (The High-High
B-channel selection)

18 Interdigit Timer 1

Select the Interdigit timer value to time-out during dial tone.

Possible values:1~180 (default = 15)

19 Interdigit Timer 2

Interdigit timer value to time-out after the first digit is dialed.

Possible values:1~180 (default = 5)

20 CESID

Enter the CESID value for 911 calls.

Possible values:Up to 16 ASCII characters (default = no value)

21 Number Voice Calls

Allowed

Select the Number of Voice Calls Allowed. If a selection is not made, previously
written data in this field is erased.

Possible values:One or Two (default)

Note

If One is selected the other channel is reserved for Data.

22 Service Tone

Permission

Enable Service Tone Permission. Select Disable for modems and faxes.

Possible values:Enable or Disable (default = Disable)

23 TGAC Override

Enable TGAC Override.

Possible values:Enable or Disable (default = Disable)

24 Set System Speed

Dial

Enable System Speed Dial changing permission.

Possible values:Enable or Disable (default = Disable)

25 Network COS

Enter the Network COS value. If a selection is not made, previously written data in
this field is erased.

Possible values:1~32 (default = 1)

26 DN2~32 DN8

Add a DN to this BRI Station. When a DN is entered into one of the seven available
fields, default data as defined in

217 ISDN Station Data

is applied to the DNs. If a

selection is not made, any previously written data in this field is erased.

Possible values:Up to 5 ASCII characters (default = no value)

IELD

ESCRIPTION

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands

Strata CIX 200, Programming Manual

Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands