manualshive.com logo in svg

Strata CIX 200, Programming Manual

The "Strata CIX 200" General Description Manual is a comprehensive guide for users of this advanced telecommunication system. This manual provides in-depth information about its features, functions, and troubleshooting, enabling users to maximize the potential of their device. Download this manual for free from our website and become an expert user of Strata CIX 200. [Website]

Share
Download
background image

Operation

System Setup

Strata CIX Programming Vol.1    12/09

10-5

Oper

ation

908 Secure Digital and SmartMedia

This program enables you to format and perform file management tasks on a Secure Digital or SmartMedia 
card while it is installed in the CIX processor. Secure Digital (SD) cards are required for ACTU3A (CIX100), 
BCTU2A (CIX670) and HCTU1A (CIX1200) processor cards.

Select Maintenance > SM/DS Card.

Secure Digital or SmartMedia Card

The SD card is replacing the SmartMedia (SM) card for use as a removable, portable memory device. The 
SD is physically smaller than the SM card while storage capacity is the same or greater.

Notes

•

32MB or 64MB must be used for Strata CIX maintenance functions.

•

The Strata CIX does not use Compact Flash or other similar types of small storage devices.

Functions

An SD or SM Card(s) is required for most of the important Strata CIX maintenance functions such as:

•

Saving (Backup) and re-loading the programmed database of a particular Strata CIX system.

•

Saving Event trace data files for troubleshooting problems.

•

Updating or upgrading the Strata CIX operating software version.

Note

The procedure below will refer to the SM/SD card. The same procedures are used for both the 
SmartMedia and Secure Digital card.

Administration and Use

•

When the SM/SD card is used to perform one of its functions, it is installed in the SM/SD slot of the 
Strata CIX processor. It must be first formatted for Strata CIX operation by running Forced Format 
(Program 908). Using the PC to format the SM/SD card is not recommended.

•

The Strata CIX format will create five special folders. These folders and how to use them are explained 
below and in Chapter 14–Data Backup and Restore.

1. Install the SM/SD Card into the SM/SD slot of the Strata CIX processor.

2. Select Maintenance > SM/SD Card.

3. Click one of the following:

•

Normal Format – creates any CIX SM/SD folder that does not exist already. Existing folders are not 
overwritten by this procedure.

Time Adjustment

Defines the exact amount of time change. Default is one hour. The time 
adjustment should not be long enough to cause a date change.

Change based on 
Date and Time

DST change can be set two ways:
1. Day of the week: time will change based on the Month, Time and Day of the 
week set in this program
2. Date: time will change base on the Date and Time set in this program

Default:

Day of the week

F

IELD

D

ESCRIPTION

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Sony Ericsson Xperia X10 Extended User Manual preview
Xperia X10
Brand: Sony Ericsson Pages: 113
Micromax AD4500 Manual preview
AD4500
Brand: Micromax Pages: 40
Plum Z513 User Manual preview
Z513
Brand: Plum Pages: 21
AirTyme GTX75 User Manual preview
GTX75
Brand: AirTyme Pages: 159
Iget BLACKVIEW BV6000 Quick Start Manual preview
BLACKVIEW BV6000
Brand: Iget Pages: 52
Xiaomi Mi 9 Lite User Manual preview
Mi 9 Lite
Brand: Xiaomi Pages: 52
IPRO i9 Manual preview
i9
Brand: IPRO Pages: 66
LG 329G User Manual preview
329G
Brand: LG Pages: 20
LG 490 User Manual preview
490
Brand: LG Pages: 83
LG 420G User Manual preview
420G
Brand: LG Pages: 18
LG 430G User Manual preview
430G
Brand: LG Pages: 61
LG 320G Quick Start Manual preview
320G
Brand: LG Pages: 2
LG 325G User Manual preview
325G
Brand: LG Pages: 111
LG 221C (Spanish) Guía Del Usuario preview
221C
Brand: LG Pages: 110
LG 328BG User Manual preview
328BG
Brand: LG Pages: 121
LG 441G User Manual preview
441G
Brand: LG Pages: 186
LG 306G Service Manual preview
306G
Brand: LG Pages: 26
LG 1150 User Manual preview
1150
Brand: LG Pages: 134

Brands by name

Popular brands

Load more brands