Motorola MPC860 PowerQUICC User Manual Download Page 700 | Manualshive

Page: 700 / 1106

background image

24-16

MPC860 PowerQUICC UserÕs Manual

MOTOROLA

Part V. The Communications Processor Module

21. Write 0x001A to SCCM to allow TXE, RXF, and TXB interrupts.

22. Write 0x2000_0000 to the CPM interrupt mask register (CIMR) to allow SCC2 to

generate a system interrupt. The CICR should also be initialized.

23. Write 0x0000_0000 to GSMR_H2 to enable normal CTS and CD behavior with

idles (not ßags) between frames.

24. Write 0x0000_0000 to GSMR_L2 to conÞgure CTS and CD to control transmission

and reception in HDLC mode. Normal Tx clock operation is used. Notice that the
transmitter (ENT) and receiver (ENR) have not been enabled. If inverted HDLC
operation is preferred, set RINV and TINV.

25. Write 0x0000 to PSMR2 to conÞgure one opening and one closing ßag, 16-bit

CCITT-CRC, and prevent multiple frames in the FIFO.

26. Write 0x00000030 to GSMR_L2 to enable the SCC2 transmitter and receiver. This

additional write ensures that ENT and ENR are enabled last.

Note that after 5 bytes and CRC have been sent, the Tx buffer is closed; the Rx buffer is
closed after a frame is received. Frames larger than 256 bytes cause a busy (out-of-buffers)
condition because only one RxBD is prepared.

24.13.2 SCC HDLC Programming Example #2

The following sequence initializes an HDLC channel that uses the DPLL in a Manchester
encoding. Provide a clock which is 16

´

the chosen bit rate of CLK3. Then connect CLK3

to the HDLC transmitter and receiver. (A baud rate generator could be used instead.)
ConÞgure SCC2 to use RTS2, CTS2, and CD2.

1. Follow steps 1Ð23 in example #1 above.

2. Write 0x004A_A400 to GSMR_L2 to make carrier sense always active, a 16-bit

preamble of Ô01Õ patterns, 16

´

operation of the DPLL and Manchester encoding for

the receiver and transmitter, and HDLC mode. CTS and CD should be conÞgured to
control transmission and reception. Do not set GSMR[ENT, ENR].

3. Write 0x0000 to PSMR2 to use one opening and one closing ßag and 16-bit

CCITT-CRC and to reject multiple frames in the FIFO.

4. Write 0x004A_A430 to GSMR_L2 to enable the SCC2 transmitter and receiver.

This additional write to GSMR_L2 ensures that ENT and ENR are enabled last.

24.14 HDLC Bus Mode with Collision Detection

The HDLC controller includes an option for hardware collision detection and
retransmission on an open-drain connected HDLC bus, referred to as HDLC bus mode.
Most HDLC-based controllers provide only point-to-point communications; however, the
HDLC bus enhancement allows implementation of an HDLC-based LAN and other
point-to-multipoint conÞgurations. The HDLC bus is based on techniques used in the
CCITT ISDN I.430 and ANSI T1.605 standards for D-channel point-to-multipoint
operation over the S/T interface. However, the HDLC bus does not fully comply with I.430

«
...
698
699
700
701
702
...
»

Summary of Contents for MPC860 PowerQUICC



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC860 PowerQUICC

Brand: Eaton Pages: 16

Brand: Waterway Pages: 16

Brand: Bartec Pages: 26

Brand: Vacon Pages: 50

Brand: Elby Designs Pages: 4

Brand: SOMFY Pages: 56

Brand: Texas Instruments Pages: 27

1020 CAN-RS232-RS422 MFL

Brand: PENKO Pages: 29

Brand: Goodson Pages: 4

Brand: Moeller Pages: 2

Brand: Atmel Pages: 12

Brand: D-M-E Pages: 15

Brand: Alcor Micro Pages: 18

Brand: Parker Pages: 64

TWRF1 SCR Series

Brand: Metek Pages: 36

Brand: Tyco Pages: 32

Brand: CDVI Pages: 24

Brand: METRON Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands