MOTO GUZZI California EV V1100 Service Station Manual Download

Page: 68 / 173

transmission is housed shall be 75 mm

(2.95 in).

Gear selector

Checking the gear selector

Check that the control rocker on the pegs of the grooved drum is not hardened, and that the two nibs

are not ginned, otherwise replace it.

Flywheel

Removing the flywheel

•

Remove the clutch.

•

Position the locking tool on the flywheel

and loosen the six flywheel fixing

screws operating diagonally and in

stages.

•

Remove the locking tool.

Specific tooling

12.91.18.01

Tool to lock the flywheel and the

starting ring gear

•

Remove the flywheel.

See also

Disassembling the

clutch

Checking

•

Check that the flywheel surface that contacts the plate is not scratched.

Engine

California EV V1100

ENG - 68

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands