manualshive.com logo in svg

MOTO GUZZI California EV V1100, Service Station Manual

Share
Download
MOTO GUZZI California EV V1100 Service Station Manual Download Page 30

•

Unscrew and remove the filler plug with

dipstick.

•

Drain the oil into the container; allow

several minutes for oil to drain out com-

pletely.

•

Check and, if necessary, replace the

drainage plug sealing washers.

•

Remove any metal scrap attached to

the drainage plug magnet.

•

Screw and tighten the drainage plug.

•

Pour new oil until it goes above the

minimum level marked "MIN".

Engine oil filter

•

Drain the engine oil.

•

Unscrew and remove the eighteen

screws.

•

Remove the oil sump.

CARTRIDGE-TYPE ENGINE OIL FILTER

•

Unscrew the filtering cartridge.

•

Install a new original cartridge in the

appropriate seat tightening it by hand

to avoid an excessive tightening.

Maintenance

California EV V1100

MAIN - 30

Summary of Contents for California EV V1100














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands