MOTO GUZZI California EV V1100 Service Station Manual Download

Page: 41 / 173

CHECK THE WINDING ISOLATION TOWARDS EARTH

Connect one connecting point of the ohmmeter to one of the two yellow cables and the other connecting

point to earth (laminar pack). The instrument should indicate a value above 10 MW.

CHECK THE WINDING CONTINUITY

Connect the two connecting points of the ohmmeter to the two yellow cables.

The instrument should indicate a value of 0.2 - 0.3 W.

CHECK THE VOLTAGE OUTPUT

Connect an alternate 200 Volt capacity voltmeter to the two yellow cables.

Start the motor and check that the voltage output is included within the values indicated in the table.

ALTERNATOR CHECK

Specification

Desc./Quantity

Alternating current voltage at 1000 rpm

higher or equal to 15V

Alternating current voltage at 3000 rpm

higher or equal to 40V

Alternating current voltage at 6000 rpm

higher or equal to 80V

Direct current intensity at 1000 rpm

9.50 Amp

Direct current intensity at 1200 rpm

13.0 Amp

Direct current intensity at 1500 rpm

16.50 Amp

Direct current intensity at 2000 rpm

20.0 Amp

Direct current intensity at 3000 rpm

23.50 Amp

Direct current intensity at 4000 rpm

25.0 Amp

Direct current intensity at 6000 rpm

26.50 Amp

Direct current intensity at 10000 rpm

27.50 Amp

Voltage regulator check

The regulator has been calibrated in order to maintain the battery voltage at a value between 14 - 14.6

Volts. The pilot light (illuminated when the engine is not running, but the key is in ON position) will switch

off when the generator begins to charge, (approx. 700 rpm).

Regulator checks

Normal work-shop tools are generally insufficient for regulator checking, however, listed below are

certain operations that can be carried out in order to detect regulators that are defective.

The regulator is certainly defective if:

After having isolated it from the rest of the system short circuits can be detected between the earth

(aluminium casing) and any of the output cables.

See also

Checking the stator

California EV V1100

Electrical system

ELE SYS - 41

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands