manualshive.com logo in svg

MOTO GUZZI California EV V1100, Service Station Manual

Share
Download
MOTO GUZZI California EV V1100 Service Station Manual Download Page 168

the ECU) and the air temperature sensor are posi-

tioned upstream of the throttle valve.

•

Remove the front saddle.

•

Remove the fuel tank.

•

Remove the side fairings.

•

Loosen the clamps that secure the filter

box to the throttle body and move the

connection ducts to the outside.

•

Disconnect the breather pipe located in

the front part of the filter box.

•

Unscrew the frame fixing screw (1).

•

Unscrew the two screws (2) and re-

move the U-bolt.

•

Remove the air filter box.

See also

Seat

Fuel tank

Rear mudguard

CALIFORNIA EV (1997-2000)

Removal:

•

Remove the front saddle

•

Disconnect the electrical connections

(1) between the main cable assembly

and rear light wiring harness

Bodywork

California EV V1100

BODYW - 168

Summary of Contents for California EV V1100














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands