manualshive.com logo in svg

MOTO GUZZI California EV V1100, Service Station Manual

Share
Download
MOTO GUZZI California EV V1100 Service Station Manual Download Page 35

•

Remove the cables (D) from the throt-

tle body (G)

•

Loosen the two screws (C) and slide

the throttle control together with the ca-

bles off the handlebar.

Checking the valve clearance

CAUTION

IF CLEARANCE IS LARGER THAN RECOMMENDED, THE TAPPETS WILL BE NOISY. OTHER-
WISE, THE VALVES DO NOT CLOSE CORRECTLY, WHICH CAN LEAD TO PROBLEMS SUCH
AS:

•

PRESSURE DROP;

•

ENGINE OVERHEAT;

•

VALVE BURN OUT, ETC.

OPTION 02

HYDRAULIC TAPPET:

It is not necessary to perform the valve clearance

as the hydraulic tappets automatically cancel the

valve clearance during the engine operation, al-

ways keeping the camshaft in contact with the

bucket tappets.

CAUTION

IF CLEARANCE IS LARGER THAN RECOMMENDED, THE TAPPETS WILL BE NOISY. OTHER-
WISE, THE VALVES DO NOT CLOSE CORRECTLY, WHICH CAN LEAD TO PROBLEMS SUCH
AS:

•

PRESSURE DROP;

•

ENGINE OVERHEAT;

•

VALVE BURN OUT, ETC.

OPTION 02

California EV V1100

Maintenance

MAIN - 35

Summary of Contents for California EV V1100














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands