manualshive.com logo in svg

MOTO GUZZI California EV V1100, Service Station Manual

Share
Download
MOTO GUZZI California EV V1100 Service Station Manual Download Page 167

Removal:

•

Unscrew the 4 nuts that secure it to the inside of the rear mudguard

Driving mirrors

Removal:

•

Unscrew the upper nut (1), integral with

the mirror, while holding the lower one

(2) using the two keys as in the figure;

•

Remove mirror by unscrewing it.

Side body panels

Removal:

•

Unscrew the 2 screws (1) fixing it to the

frame

•

Remove the fairing (2) from the motor-

cycle

Air box

<span style="FONT-SIZE: 12pt; FONT-FAMILY:

"Times New Roman"; mso-fareast-font-family:

"Times New Roman"; mso-ansi-language: IT;

mso-fareast-language: IT; mso-bidi-language:

AR-SA">The circuit is composed of: air filter, in-

take manifold, throttle body. The throttle position

potentiometer is splined onto the throttle shaft.

<span style="FONT-SIZE: 12pt; FONT-FAMILY:

"Times New Roman"; mso-fareast-font-family:

"Times New Roman"; mso-ansi-language: IT;

mso-fareast-language: IT; mso-bidi-language:

AR-SA">The absolute pressure sensor (integral to

California EV V1100

Bodywork

BODYW - 167

Summary of Contents for California EV V1100














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands