manualshive.com logo in svg

MOTO GUZZI California EV V1100, Service Station Manual

Share
Download
MOTO GUZZI California EV V1100 Service Station Manual Download Page 115

Front

Removing the front wheel

•

Place a support under the motorcycle, which allows to lift the front wheel off the ground.

•

Remove the brake callipers.

•

Loosen the two screws fixing the pin to the fork legs.

•

Remove the pin, the spacers and remove the wheel.

Installing the front wheel

•

Insert the complete wheel between the fork legs.

•

Lubricate the shank and thread of the wheel axle with the recommended grease.

•

Grease the threads present in the left fork leg.

•

Place the spacers and tighten the wheel axle.

•

Tighten the two screws fixing the spindle to the fork leg to the specified torque.

•

Refit the clamp or brake callipers tightening the fixing screws to the specified torque.

•

Check that the discs slide freely within the clamps, then repeatedly actuate the brake lever

to bring the clamps pistons back in the normal position.

Front fork

Diagram

California EV V1100

Suspensions

SUSP - 115

Summary of Contents for California EV V1100














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands