MOTO GUZZI California EV V1100 Service Station Manual Download

Page: 148 / 173

•

If the contact is like this, the pinion is

too far away from the rotation axis of

the crown: approach the pinion by in-

creasing the spacer thickness between

bearing and pinion.

•

If the contact is like this, the crown is

too far from the pinion rotation axis: ap-

proach the crown by reducing the

spacer thickness between box and

cover.

•

With a proper coupling, the clearance

between the pinion teeth and the teeth

of the crown should be between 0.10 -

0.15 mm (0.0039 - 0.0059 in).

Pedaline

Rimozione

GEAR SHIFT REMOVAL

•

Undo the 3 screws (A)

•

Remove the cradle cover (B)

•

Unscrew the nut (C)

•

Undo the screw (D)

•

Remove the gearbox lever (E)

Chassis

California EV V1100

CHAS - 148

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands