MOTO GUZZI California EV V1100 Service Station Manual Download

Page: 170 / 173

Removal:

•

Remove the front saddle

•

Disconnect the electrical connections

between the main cable assembly and

rear light wiring harness

•

Remove the rear saddle from the mud-

guard

•

Remove the lateral panels (1)

•

Remove the luggage rack (2)

•

Unscrew the 2 mudguard front fixing

screws (3) and the relative support (4)

•

Unscrew the 2 lateral fixing nuts (5)

and remove the mudguard

Fuel tank

•

Set to the ignition switch to OFF.

•

Remove the front saddle.

•

Undo and remove the fixing screw.

•

Remove the washer.

•

Lift the rear part of the tank and push it

to the side by sliding it backwards.

•

Disconnect the breather pipe (1).

•

Disconnect the quick coupling (2) of

the fuel pipe.

CAUTION

PLACE A CLOTH UNDER THE QUICK

COUPLING TO RECOVER ANY FUEL LEAK.

<span style="FONT-SIZE: 12pt; FONT-FAMILY: "Times New Roman"; mso-fareast-font-family: 'Times

New Roman'; mso-ansi-language: IT; mso-fareast-language: IT; mso-bidi-language: AR-SA">

Bodywork

California EV V1100

BODYW - 170

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands