MOTO GUZZI California EV V1100 Service Station Manual Download Page 29

Page: 29 / 173

•

Check oil level by means of the oil dip-

stick.

•

The oil level is correct when it close to

the "MAX" mark.

MAX

= maximum level

MIN = minimum level

Add engine oil if required:

•

Unscrew and remove the cap with dip-

stick.

•

Top-up with engine oil until it goes

above the minimum level marked

"MIN".

CAUTION

DO NOT ADD ADDITIVES OR ANY OTHER SUBSTANCE TO THE FLUID. WHEN USING A FUNNEL
OR ANY OTHER ELEMENT, MAKE SURE IT IS PERFECTLY CLEAN.

Replacement

Use an engine oil type with characteristics indicated in the table of recommended products.

The other viscosity levels indicated in this table can be used if the average temperature of the motor-

bike's area of use is within the indicated range.

NOTE

HOT OIL IS MORE FLUID AND WILL DRAIN OUT MORE EASILY AND COMPLETELY.

•

Place a container with 4000 cm³ (244

cu.in) capacity under the drainage

plug.

•

Unscrew and remove the drainage

plug.

California EV V1100

Maintenance

MAIN - 29

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Brands by name

Popular brands