MOTO GUZZI California EV V1100 Service Station Manual Download Page 140

Page: 140 / 173

Checking

<span style="FONT-SIZE: 12pt; FONT-FAMILY:

"Times New Roman"; mso-fareast-font-family:

'Times New Roman'; mso-ansi-language: IT; mso-

fareast-language: IT; mso-bidi-language: AR-

SA">

Check that the swingarm does not show bending

or unsoldered parts, that the seats of the bearings

are in good condition and that the junction surface

of the right arm to the box does not have deep

scratches.

Check the wear of the bearings on the swingarm

pivot axis on the frame and the bearing on the right

arm.

<span style="FONT-SIZE: 12pt; FONT-FAMILY:

"Times New Roman"; mso-fareast-font-family:

"Times New Roman"; mso-ansi-language: IT;

mso-fareast-language: IT; mso-bidi-language:

AR-SA">To remove the bearing for the universal

joint use a special extractor.

<span style="FONT-SIZE: 12pt; FONT-FAMILY:

"Times New Roman"; mso-fareast-font-family:

"Times New Roman"; mso-ansi-language: IT;

mso-fareast-language: IT; mso-bidi-language:

AR-SA">To remove the swingarm pin bearings

use a special extractor.

NOTE

ONCE A BEARING IS REMOVED FROM ITS

SEAT IT CAN NOT BE USED AGAIN.

Cardan shaft

Removing

•

Remove the swingarm.

•

Remove the cardan shaft.

See also

Chassis

California EV V1100

CHAS - 140

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Brands by name

Popular brands