manualshive.com logo in svg

MOTO GUZZI California EV V1100, Service Station Manual

Share
Download
MOTO GUZZI California EV V1100 Service Station Manual Download Page 51

Disassembling the gearbox

To disassemble the gear in its elements operate

as follows:

•

Lock the gear support tool in vice and

mount the complete gear on the sup-

port.

•

To be able to easily perform the re-

moval, it is recommended that the gear

in neutral position.

•

Discharge all the oil from the gear.

Specific tooling

05.90.25.30

 

Gearbox support

•

Remove the caulking on the secondary

shaft lock nut.

•

Unscrew the nut using the special

spanner to lock the secondary shaft

and to undo the nut.

Specific tooling

12.90.71.00

 

Tool to lock the secondary shaft

14.90.54.00

 

Secondary shaft locking nut

•

Undo the odometer transmission and

slide it off from the gear cover.

•

Remove the crown gear together with

the ball and with the thrust washer.

California EV V1100

Engine

ENG - 51

Summary of Contents for California EV V1100














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands