manualshive.com logo in svg

MOTO GUZZI California EV V1100, Service Station Manual

Share
Download
MOTO GUZZI California EV V1100 Service Station Manual Download Page 56

Disassembling the clutch shaft

•

With the extractor code 14928500, slide off the inner track of the roller bearing and the

thickness nut (1).

•

Then place the complete shaft on a press and with a special extractor code 12905900 com-

press the spring so far to be able to slide off the two flexible coupling cap sealing semi-

sectors (2) and slide off: - The cap (3); - the springs (4); - the sleeve with coupling (5); - the

transmission gear bearing (6).

Specific tooling

14.92.85.00

 

Tool to slide off the inner track of the clutch shaft bearing

12.90.59.00

 

Clutch shaft removal

Checking the primary shaft

Primary shaft

Check the teeth of the gears, they must be free from grain and excessive consumption, otherwise

replace the shaft.

5th gear on the primary shaft

Check the teeth of the gear, they must be free from grain and excessive consumption, otherwise replace

the gear.

Bushing for 5th gear

Check that the surface where the rolls are working is smooth and are not scored or distorted, also check

the inside hollows of the bushing: they must appear smooth.

Bushing roller for 5th gear

Engine

California EV V1100

ENG - 56

Summary of Contents for California EV V1100














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands