manualshive.com logo in svg

MOTO GUZZI California EV V1100, Service Station Manual

Share
Download
MOTO GUZZI California EV V1100 Service Station Manual Download Page 153

Rear brake disc

Disc Inspection

The brake disc must be perfectly clean, without rust, oil, grease or scales and shall not show deep

scratches. If the disk has one of these anomalies, perform a thorough cleaning, if the defect still remains,

the disc must be replaced.

Rear disc thickness: 5.1 mm (0.2 in). Rear disc thickness at the wear limit: 4.9 mm (0.19 in).

If the disc is not within the above shown measurements it must be replaced.

Front brake disc

Disc Inspection

The brake discs must be perfectly clean, without rust, oil, grease or scales and shall not show deep

scratches. If the disks have one of these anomalies, perform a thorough cleaning, if the defect still

remains, the discs must be replaced.

Front disc thickness: 4.1 mm (0.16 in). Front disc thickness at the wear limit: 3.9 mm (0.15 in).

If the discs are not within the above shown measurements, they must be replaced. The front discs are

composed of a part integral with the wheel rim and a floating brake clamp. If the disc must be replaced,

it is necessary to replace both components.

Front brake pads

Removal

•

Turn the pins and remove both cotter

pins.

California EV V1100

Braking system

BRAK SYS - 153

Summary of Contents for California EV V1100














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands