manualshive.com logo in svg

MOTO GUZZI California EV V1100, Service Station Manual

Share
Download
MOTO GUZZI California EV V1100 Service Station Manual Download Page 28

•

Place a container with suitable capacity under the drainage plug (3).

•

Unscrew and remove the drainage plug (3).

•

Unscrew and remove the filling plug (2).

•

Drain the oil into the container; allow several minutes for oil to drain out completely.

•

Check and if necessary, replace the sealing washer of drainage plug (3).

•

Remove any metal scrap attached to the drainage plug (3) magnet.

•

Screw and tighten the drainage plug (3).

•

Unscrew and remove the level plug (1).

•

Pour new oil through the fill opening (2) until it reaches the level plug hole (1).

CAUTION

DO NOT ADD ADDITIVES OR OTHER SUBSTANCES TO THE FLUID. WHEN USING A FUNNEL
OR ANY OTHER ELEMENT, MAKE SURE IT IS PERFECTLY CLEAN.

•

Screw and tighten the caps (1 - 2).

Engine oil

Check

CAUTION

ENGINE MUST BE WARM TO CHECK ENGINE OIL LEVEL.

NOTE

DO NOT LET THE ENGINE IDLE WITH THE VEHICLE AT STANDSTILL TO WARM UP THE ENGINE
OIL AND REACH THE OPERATING TEMPERATURE OF ENGINE OIL. OIL IS BEST CHECKED
AFTER RUNNING FOR ABOUT 15 KM (10 miles).

•

Shut off the engine.

•

Keep the vehicle upright with both

wheels on the ground.

•

Unscrew and remove the cap with dip-

stick.

•

Clean dipstick.

•

Refit the cap with dipstick into its hole

without tightening.

•

Remove the cap with dipstick.

Maintenance

California EV V1100

MAIN - 28

Summary of Contents for California EV V1100














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands