MOTO GUZZI California EV V1100 Service Station Manual Download

Page: 125 / 173

Checking the components

Stem

Check the sliding surface for scorings and/or scratches.

These scorings can be eliminated by rubbing them with wet sandpaper (grain 1).

If the scorings are deep, replace the stem.

Use a dial gauge to check that the stem bending is below the limit value.

If over the value, replace the stem.

CAUTION

A BENT STEM SHOULD NEVER BE STRAIGHTENED BECAUSE ITS STRUCTURE WOULD BE
WEAKENED AND USING THE VEHICLE MAY BECOME DANGEROUS.

Characteristic

Bending limit:

0.2 mm (0.00787 in)

Sleeve

Check that there are no damages and/or cracks; otherwise, replace it.

Spring

Check the spring is in good conditions.

Check that the following components are in good conditions:

•

upper bushing;

•

lower bushing;

•

piston.

If there are signs of excessive wear or damage, replace the affected component.

CAUTION

REMOVE ANY IMPURITY IN THE BUSHINGS, TAKING CARE NOT TO SCRATCH THEIR SUR-
FACE.

Replace the following components with new ones:

•

seal ring;

•

dust gaiter;

California EV V1100

Suspensions

SUSP - 125

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands