manualshive.com logo in svg

MOTO GUZZI California EV V1100, Service Station Manual

Share
Download
MOTO GUZZI California EV V1100 Service Station Manual Download Page 135

•

Place a stand under the swingarm so

that the front wheel does not touch the

ground

•

Remove the left silencer

•

Unscrew the screw-pin (A) for retaining

the calliper holding plate (B)

•

Remove brake calliper (C) from the cal-

liper holding plate (B)

•

Unscrew the nut (D) with washer (E) on

the box side pin

•

Loosen the screw locking the pin (F) on

the swingarm

•

Pull out the pin (G) of the box, hub and

swingarm

•

Remove the calliper holding plate (B)

•

Tilt the vehicle on the right side enough

to be able to pull the wheel out of the

swingarm and transmission box.

CALIFORNIA EV (2001)

•

Place a stand under the swingarm so

that the front wheel does not touch the

ground.

•

Remove the left silencer

•

Remove brake calliper from the calliper

holding plate (B)

•

Unscrew the nut (D) with washer (E) on

the box side pin

•

Pull out the pin (G) of the box, hub and

swingarm

California EV V1100

Chassis

CHAS - 135

Summary of Contents for California EV V1100














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands