manualshive.com logo in svg

MOTO GUZZI California EV V1100, Service Station Manual

Share
Download
MOTO GUZZI California EV V1100 Service Station Manual Download Page 132

2) The pin (1) is screwed into the left fork leg that

is threaded, the screws (3) ensure the seal.

NOTE

THIS TYPE OF FITTING WAS IMPLEMENTED UP TO
FRAME NUMBER "KD115427"

CALIFORNIA EV (2001)

The above mentioned motorcycles are equipped from the first motorcycle produced with a pin that is

screwed directly into the fork leg.

REMOVAL TYPE 1

•

Place the vehicle on the centre stand

(if present)

•

In any case place a support under the

motorcycle, which allows to lift the front

wheel off the ground

•

Remove the screws (3) securing the

clamps to the fork legs

•

Remove the clamp or the clamps from

the brake discs;

•

With the specific wrench unscrew the

retaining nut (2) of the wheel axle

•

Loosen the 4 screws (3) fixing the pin

to the fork legs

•

Remove the pin (1) with the relative

spacers and remove the wheel

Chassis

California EV V1100

CHAS - 132

Summary of Contents for California EV V1100














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands