MOTO GUZZI California EV V1100 Service Station Manual Download Page 69

Page: 69 / 173

•

Check that the contact faces on the crankshaft are not distorted; if they are, replace the

flywheel.

Installing the flywheel

•

Position the flywheel.

NOTE

RESPECT THE FLYWHEEL POSITIONING REFERENCES.

CAUTION

THE SCREWS, AS THEY ARE SUBJECT TO

HIGH LOADS AND STRESS, MUST BE REPLACED WITH
NEW ONES AT THE FOLLOWING REFITTING.

•

Position the locking tool on the flywheel

and tighten the six flywheel fixing

screws operating diagonally and in

stages.

•

Install the clutch.

Specific tooling

12.91.18.01

Tool to lock the flywheel and the

starting ring gear

See also

Assembling the

clutch

Generator

Removing the generator

The alternator is composed of two elements:

The stator, which is fixed on the timing system

cover and the rotor which is mounted on the crank-

shaft.

California EV V1100

Engine

ENG - 69

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Brands by name

Popular brands