MOTO GUZZI California EV V1100 Service Station Manual Download

Page: 117 / 173

38 Upper bushing

39 Complete right fork leg

40 Long screw

41 Washer

42 Screw

43 Complete left fork leg

44 LH adjustment knob (compression)

45 LH pipe (compression)

46 LH rod (compression)

47 Cap

48 Calibration blade diam 12 mm (0.47 in)

48 Calibration blade diam 15 mm (0.59 in)

48 Calibration blade diam 17 mm (0.67 in)

49 LH pin (compression)

50 LH piston (compression)

51 Nut

52 RH complete fork arm

53 LH complete fork arm

54 O-Ring screw

55 OR ring

56 Cap

57 Screw

58 Washer

Adjustment

•

The vehicle is equipped with a hydraul-

ic telescopic fork with separate adjust-

ment for rebound and compression

damping.

•

The hydraulic rebound can be adjusted

by acting on the adjustment knobs (1)

and (2).

•

The left adjustment knob (1) controls

the adjustment of the hydraulic re-

bound damping.

•

The right knob (2) is the one in com-

pression.

California EV V1100

Suspensions

SUSP - 117

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands