MOTO GUZZI California EV V1100 Service Station Manual Download

Page: 141 / 173

Removing

Checking

Sleeve for transmission shaft and bevel pinion

(1).

The inner splines must be intact; free from grain or

dents, otherwise replace it.

Transmission shaft Seeger rings (2)

Check that the rings are not cracked or have lost

elasticity, otherwise replace them.

Cardan shaft (3)

The splines on the cardan shaft must be intact,

free from grain or dents.

Check that the joint is not hardened or too loose,

otherwise replace it.

See also

Removing

Bevel gears

Removing

•

Remove the rear wheel.

•

Drain the oil from the transmission box.

•

Undo and remove the four nuts.

•

Remove the transmission box.

•

Detach the casing (1) from the box

complete with the pinion (2) with gas-

ket (OR) (3).

California EV V1100

Chassis

CHAS - 141

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands