manualshive.com logo in svg

MOTO GUZZI California EV V1100, Service Station Manual

Share
Download
MOTO GUZZI California EV V1100 Service Station Manual Download Page 160

Rimozione

REAR BRAKE LEVER REMOVAL

•

Undo the 2 screws (A) and remove the

cradle cover (B)

•

Remove the cotter pin (C) and slide off

the pin (D)

•

Undo the screw (E) and remove the

brake lever (F)

Rear brake pump - combined

Removal

It is a mechanical device connected to the rear swingarm by a spring; based on its position (thus as a

result of the weighing load on the rear axle load), the valve in the distribution mechanism distributes

the brake oil pressure of the integral system integral in varying proportions between the front and rear

calliper (increasing the load on the rear, increases the pressure on the rear calliper and vice versa).

This ensures a more secure braking limiting the possibility of locking of the wheels.

NOTE

<span style="FONT-SIZE: 12pt; FONT-FAMILY: "Times New Roman"; mso-fareast-font-family: 'Times
New Roman'; mso-ansi-language: IT; mso-fareast-language: IT; mso-bidi-language: AR-SA">

THE

SYSTEM OPERATES IN ACCORDANCE WITH THE CALIBRATION OF THE REAR SHOCK AB-
SORBERS, REPLACING THEM WITH OTHERS OF DIFFERENT TECHNICAL CHARACTERISTICS
COMPROMISES THE SYSTEM OPERATION.

Braking system

California EV V1100

BRAK SYS - 160

Summary of Contents for California EV V1100














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands