MOTO GUZZI California EV V1100 Service Station Manual Download Page 112

Page: 112 / 173

•

Connect the dipstick (1) of the left side

throttle body.

•

Start the engine and bring the temper-

ature to 50°C (122 ° F) (readable on

AXONE) after selecting the engine

temperature parameter.

•

Fully close the by-pass (4) on both

sides

•

Disconnect the dipstick (1) of the left

side throttle body;

•

Level the depression in the right cylin-

der with the throttle adjustment dowel

(5).

•

Connect the dipstick (1) of the left side

throttle body.

•

Check out of the idle (2000/3000 RPM

approximately) the balance of the de-

pression between the two cylinders. In

case of separation, act on the adjuster

screw (6) and level the depression.

•

Gradually open both bypasses so as to

bring the idle speed to 1100 +/- 50

RPM readable on AXONE after select-

ing the rpm parameter, while maintain-

ing balanced the depression.

•

The engine temperature should range

between 70°C (158°F) and 80°C (176°

F).

•

Disconnect the vacuum gauge and

check the idle speed.

•

Turn off and disconnect AXONE.

CAUTION

Power supply

California EV V1100

P SUPP - 112

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Brands by name

Popular brands