MOTO GUZZI California EV V1100 Service Station Manual Download

Page: 32 / 173

•

Place a container with suitable capaci-

ty under the drainage plug (3).

•

Unscrew and remove the drainage

plug (3).

•

Unscrew and remove the filler plug (2).

•

Drain the oil into the container; allow

several minutes for oil to drain out com-

pletely.

•

Check and if necessary, replace the

drainage plug (3) sealing washers.

•

Remove any metal scrap attached to

the drainage plug (3) magnet.

•

Screw and tighten the drainage plug

(3).

•

Unscrew and remove the dipstick (1).

•

Pour in new oil from the filling hole (2),

until it reaches the dipstick opening (1).

•

Tighten the filler plug (2) and the dip-

stick (1).

CAUTION

DO NOT ADD ADDITIVES OR OTHER SUBSTANCES TO
THE FLUID. WHEN USING A FUNNEL OR ANY OTHER EL-
EMENT, MAKE SURE IT IS PERFECTLY CLEAN.

See also

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands