MOTO GUZZI California EV V1100 Service Station Manual Download Page 34

Page: 34 / 173

Throttle grip cables replacement

ACCELERATOR CONTROL

The throttle control handgrip, in all steering posi-

tions, must have a free play of 1.5 - 2 mm (0.059 -

0.079 in). If required, adjust it; act on the specific

adjuster screws (A) located in the control itself.

Check by acting on the control, the smooth oper-

ation of the inner cables: if there is friction or

jamming, replace them

THROTTLE GRIP CABLES MAINTENANCE

•

Remove the right device (B) by un-

screwing the two fixing screws (C);

•

Grease the end of the cables (D) and

the pulley (E)

•

Carefully close the throttle control

again inserting the cables (D) in the

pulley of the throttle control moving

body (E)

•

Lock the right device with the two fixing

screws (C).

CAUTION

THE LATEST SERIES OF PRODUCED California EV
(1997-2000) MOTORCYCLE HAS MOUNTED THE DESMO-
DROMIC THROTTLE CONTROL (DOUBLE TRANSMISSION
FROM FRAME NO. KD115984

Removal

•

Remove the throttle body covers (F)

Maintenance

California EV V1100

MAIN - 34

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Brands by name

Popular brands