MOTO GUZZI California EV V1100 Service Station Manual Download

Page: 136 / 173

•

Remove the calliper holding plate (B)

and the spacer (H)

•

Tilt the vehicle on the right side enough

to be able to pull the wheel out of the

swingarm and transmission box.

WHEEL HUB REMOVAL

REMOVAL

•

Undo the screw (A)

•

Remove the ring retaining plate (B)

•

Remove the circlip (C) with the help of

a special clamp and screwdriver

•

Remove the flexible coupling plate (D)

•

When the plate is removed, the flexible

coupling rubbers will be visible (E),

which must be replaced if damaged.

Spoke tension adjustment

Chassis

California EV V1100

CHAS - 136

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands