MOTO GUZZI California EV V1100 Service Station Manual Download Page 94

Page: 94 / 173

Specification

Desc./Quantity

(1.85137 - 1.85236 inch )

fitting clearance

0.025 - 0.066 mm

(0.00098 - 0.00260 inch)

CAMSHAFT (CAM) SUPPORT DIAMETER AND THEIR SEATS ON THE CRANKCASE

(FLYWHEEL SIDE)

Specification

Desc./Quantity

Shaft support diameter

32.000 - 31.984 mm

(1.25984 - 1.25921 inch)

Seat diameter on crankcase

32.025 - 32.050 mm

(1.26082 - 1.26181 inch)

fitting clearance

0.025 - 0.066 mm

(0.00098 - 0.00260 inch)

Installing the camshaft

NOTE

FOR TIMING SYSTEM REFITTING, IT IS NECESSARY TO HEAT THE ENGINE WITH A SUITABLE
HEATER IN ORDER TO INSERT THE CAMSHAFT CORRECTLY AND WITHOUT DAMAGING IT.

Follow the camshaft removal instructions but in reverse order.

Timing

To check distribution timing, follow these instruc-

tions:

•

Obtain a clearance between rockers

and valves of 1.5 mm (0.059 in);

•

Place the hub for graduated dial and

the relative graduated dial on the

crankshaft slot, inserting the spacer

and fixing it to the shaft with the nut.

Specific tooling

65.92.84.00

Graduated dial hub

19.92.96.00

Graduated dial to control ignition

timing

•

With a screw, fasten the specific arrow to the threaded hole to the left of the crankcase.

Specific tooling

17.94.75.60

Arrow to control ignition timing

•

Fit the dial gauge support and then the gauge itself on the left outer spark plug hole.

Engine

California EV V1100

ENG - 94

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Brands by name

Popular brands