MOTO GUZZI California EV V1100 Service Station Manual Download

Page: 90 / 173

•

With a specific tool (1) commercially

available extract the hydraulic tappet

(2)

•

Using a piece of thin metal wire (3),

press on the inner ball of the tappet (2)

using the upper hole;

•

Direct the tappet downwards and

pump until discharging the residual oil;

DISCHARGE THE OIL IN A SUITABLE CONTAINER

NOTE

THE TAPPET IS DISCHARGED WHEN IT CAN BE COM-
PRESSED BY PRESSING WITH ONE FINGER

See also

Removing the engine from the vehicle
Removing the

cylinder head

Removing the phonic wheel

•

Remove the timing chain.

•

Slide off the tone wheel and collect the

plug.

See also

Chain removal

Removing the camshaft

•

Remove the timing chain.

•

Remove the tone wheel.

Engine

California EV V1100

ENG - 90

Summary of Contents for California EV V1100














































































































































































Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands

MOTO GUZZI California EV V1100, Service Station Manual

Search results

Summary of Contents for California EV V1100

Reviews:

Related manuals for California EV V1100

Brands by name

Popular brands