manualshive.com logo in svg

MOTO GUZZI California EV V1100, Service Station Manual

Share
Download
MOTO GUZZI California EV V1100 Service Station Manual Download Page 129

Rear

Shock absorbers

Adjusting

The motorcycle is equipped with shock absorbers

with hydraulic rebound damping adjustment.

Turn the adjustment control on the ring nut (1) to

adjust the shock absorber hydraulic rebound

damping.

Depending on the need and the load on the mo-

torcycle, there are multiple adjustment positions;

from position "1" very soft (minimum hydraulic

damping) to position "11" very rigid (maximum hy-

draulic damping).

The shock absorber is factory set to "4".

TO OBTAIN A GOOD STABILITY IN YOUR MOTORCYCLE,
MAKE SURE THAT BOTH SHOCK ABSORBERS ARE AD-
JUSTED AT THE SAME POSITION

Removing

•

Remove the rear frame cover panels

•

Remove the upper screws (1) of the shock absorbers

•

Unscrew the lower screws (2) of the shock absorbers and remove them

California EV V1100

Suspensions

SUSP - 129

Summary of Contents for California EV V1100














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands