manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 240

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect all power cords; then, remove the
cover (see “Removing the cover” on page 195).

Step 3.

Remove the rear two hard-disk-drive kit that contains the adapter (see “Removing the rear two
hard-disk-drive kit” on page 224).

0000

0000

0000

0000

00000000

00000000

00000000

00000000

Adapter

Adapter
connector

Expansion-slot
cover

Bracket

Rear two hard-disk-drive kit

Figure 150. Adapter removal

Step 4.

Disconnect any cables from the adapter (make note of the cable routing, in case you reinstall
the adapter later).

Step 5.

Carefully grasp the adapter by its top edge or upper corners, and pull the adapter from the rear
two hard-disk-drive kit.

Step 6.

If you are instructed to return the adapter, follow all packaging instructions, and use any packaging
materials for shipping that are supplied to you.

Replacing an adapter

Use this information to replace an adapter.

Notes:

• If your adapter was previously configured, backup or record its configuration information, if possible,

before replacing the adapter. See the documentation for your adapter for information and instructions.

• If you are replacing a ServeRAID adapter, import your RAID configuration to the replacement adapter as

a foreign configuration after you finish the replacement. See the

ServeRAID-M Software User Guide

at

https://support.lenovo.com/us/en/documents/migr-5086126 for instructions.

Replacing an adapter in a PCI riser-card assembly

The following notes describe the types of adapters that the server supports and other information that
you must consider when you install an adapter.

• Locate the documentation that comes with the adapter and follow those instructions in addition to

the instructions in this section.

• The server provides one internal SAS/SATA RAID connector and two PCI slots on the system board.

See “System-board optional-device connectors” on page 32 for the location of the internal SAS/SATA
RAID connector and riser-card slots. You can replace the Lenovo ServeRAID SAS/SATA adapter with
an optional Lenovo ServeRAID SAS/SATA adapter in the slot. For configuration information, see the
ServeRAID documentation at http://www.lenovo.com/support.

228

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands