manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 345

Automatically notify support

No

Alert Category

System - other

SNMP Trap ID

22

CIM Information

Prefix:

IMM

ID:

0040

User Response

Information only; no action is required.

•

40000029-00000000 : Security: Userid: [arg1] had [arg2] login failures from an SSH client at IP

address [arg3].

This message is for the use case where a user has failed to log in to a Management Controller from SSH.

May also be shown as 4000002900000000 or 0x4000002900000000

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

System - Remote Login

SNMP Trap ID

30

CIM Information

Prefix:

IMM

ID:

0041

User Response

Complete the following steps until the problem is solved:

1. Make sure that the correct login ID and password are being used.

2. Have the system administrator reset the login ID or password.

•

4000002a-00000000 : [arg1] firmware mismatch internal to system [arg2]. Please attempt to flash

the [arg3] firmware.

This message is for the use case where a specific type of firmware mismatch has been detected.

May also be shown as 4000002a00000000 or 0x4000002a00000000

Severity

Error

Appendix A. Integrated management module II (IMM2) error messages

333

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands