manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 239

Note:

If you are replacing a high power graphics adapter, you might need to disconnect the internal power

cable from the system board before removing the adapter.

To remove an adapter, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect all power cords; then, remove the
cover (see “Removing the cover” on page 195).

Step 3.

Remove the PCI riser-card assembly that contains the adapter (see “Removing a PCI riser-card
assembly” on page 221).

• If you are removing an adapter from PCI expansion slot 1, 2, or 3, remove PCI riser-card

assembly 1.

• If you are removing an adapter from PCI expansion slot 4, 5, or 6, remove PCI riser-card

assembly 2.

00

00000

00000

00000

000000

000000

000000

000000

00000

00000

00000

0000000

0000000

0000000

0000000

0000000

00

0

PCI
riser-card
assembly
(in long position)

Adapter

Adapter
connectors

PCI
riser-card
assembly
(in short position)

Adapter

Adapter
connectors

Full-length
adapter
bracket

Full-length
adapter
bracket

Figure 149. Adapter removal

Step 4.

Disconnect any cables from the adapter (make note of the cable routing, in case you reinstall
the adapter later).

Step 5.

Carefully grasp the adapter by its top edge or upper corners, and pull the adapter from the PCI
expansion slot.

Step 6.

If the adapter is a full-length adapter in the upper expansion slot of the PCI riser-card assembly
and you do not intend to replace it with another full-length adapter, remove the full-length-adapter
bracket and store it on the underside of the top of the PCI riser-card assembly.

Step 7.

If you are instructed to return the adapter, follow all packaging instructions, and use any packaging
materials for shipping that are supplied to you.

Removing an adapter from the rear two hard-disk-drive kit

Use this information to remove an adapter from the rear two hard-disk-drive kit.

You can only install SeveRAID-H1110 adapter in the rear two hard-disk-drive kit.

To remove an adapter, complete the following steps:

Chapter 6

.

Removing and replacing components

227

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands