manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 87

Installation tool

Microprocessor

Cover

Figure 60. Installation tool cover removal

c.

Align the installation tool with the microprocessor socket. The installation tool rests flush on
the socket only if properly aligned.

Figure 61. Installation tool alignment

d.

Install the microprocessor using the following instructions for your installation tool.

• If using Installation Tool A, twist the handle on the microprocessor tool assembly

counterclockwise to the open position to insert the microprocessor into the socket, and
lift the installation tool out of the socket.

• If using Installation Tool B, twist the handle of the installation tool assembly counterclockwise

until the microprocessor is inserted into the socket, and lift the installation tool out of the
socket. The following illustration shows the tool handle in the open position.

Chapter 2

.

Installing optional devices

75

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands