manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 442

•

800b010a-1e81ffff : Redundancy Lost for [RedundancySetElementName] has asserted. (Fan

Zone 1)

This message is for the use case when Redundancy Lost has asserted.

May also be shown as 800b010a1e81ffff or 0x800b010a1e81ffff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Fan Failure

SNMP Trap ID

11

CIM Information

Prefix:

PLAT

ID:

0802

User Response

1. Make sure that the connectors on fan n are not damaged.

2. Make sure that the fan n connectors on the system board are not damaged.

3. Make sure that the fans are correctly installed.

4.

Reseat the fans.

5. Replace the fans. (n = fan number)

•

800b010a-1e82ffff : Redundancy Lost for [RedundancySetElementName] has asserted. (Fan

Zone 2)

This message is for the use case when Redundancy Lost has asserted.

May also be shown as 800b010a1e82ffff or 0x800b010a1e82ffff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Fan Failure

SNMP Trap ID

11

430

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands