Lenovo System x3650 M4 HD Installation And Service Manual Download Page 656

Page: 656 / 1168

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0126

User Response

Make sure that DIMMs are installed in the correct sequence and have the same size, type, speed,
and technology.

•

806f070c-200cffff : Configuration Error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]. (DIMM 12)

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has been corrected.

May also be shown as 806f070c200cffff or 0x806f070c200cffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0126

User Response

Make sure that DIMMs are installed in the correct sequence and have the same size, type, speed,
and technology.

•

806f070c-200dffff : Configuration Error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]. (DIMM 13)

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has been corrected.

May also be shown as 806f070c200dffff or 0x806f070c200dffff

Severity

Error

Serviceable

Yes

644

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands