Lenovo System x3650 M4 HD Installation And Service Manual Download Page 1113

Page: 1113 / 1168

6. Run the test again.

7. Execute the standard DSA memory diagnostics to validate all memory.

8. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

202-902-000 : MemStr Test Failed

Memory size is insufficient to run the test.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Ensure that all memory is enabled by checking the "Available System Memory" in the "Resource

Utilization" section of the DSA Diagnostic Event log.

2. If necessary, access the Configuration/Setup Utility program by pressing F1 during system

boot and enable all memory.

3. Make sure that the DSA Diagnostic code is at the latest level.

4. Run the test again.

5. Execute the standard DSA memory diagnostics to validate all memory.

6. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA Nvidia GPU test results

The following messages can result when you run the Nvidia GPU test.

Appendix C. DSA diagnostic test results

1101

«
...
1111
1112
1113
1114
1115
...
»

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands