Lenovo System x3650 M4 HD Installation And Service Manual Download Page 312

Page: 312 / 1168

Thumbscrew

Handle

Figure 230. System board installation

Step 3.

Reconnect to the system board the cables that you disconnected. See “Internal cable routing and
connectors” on page 179.

Step 4.

Rotate the system-board thumbscrews toward the rear of the server until the latch clicks into place.

Step 5.

Install the fan bracket (see “Replacing the fan bracket” on page 245).

Step 6.

Install the hot-swap fans (see “Replacing a hot-swap fan” on page 242).

Note:

Remember to insert the hot-swap drive backplane cables in between the hot-swap fans as

shown in the illustration. Do not leave the cables on top of the hot-swap fans.

300

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands