manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 204

Power
cable

Configuration
cable

Backplane

Power
cable

Configuration
cable

Backplane

Backplane

Configuration
cable

Power
cable

Mini-SAS cable

Mini-SAS cable

Mini-SAS cable

Figure 113. 24x2.5-inch hot-swap HDD model cable connection

16x2.5-inch and 16x1.8-inch drive model

The internal routing and connectors for the 16x2.5-inch and 16x1.8-inch drive model cables.

The following illustration shows the internal routing and connectors for the 16x2.5-inch and 16x1.8-inch
drive model.

Note:

Make sure that Port 1 on the hardware ServeRAID is connected to Port 1 on the backplane. Likewise,

Port 0 on the hardware ServeRAID should be connected to Port 0 on the backplane.

192

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands