manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 208

0

0

0

0

0

0

0

000000000000

000000000000

000000000000

000000000000

000000000000

000000000000

000000000000

Cover-release
latch

1

2

3

Figure 117. Cover removal

Step 4.

Pull up firmly on the blue latch on the top (in the center of the front of the server) of the cover and
slide the cover toward the rear of the server until the cover has disengaged from the chassis.

Step 5.

Lift the server cover off the server and set it aside.

Attention:

For proper cooling and airflow, replace the server cover before you turn on the server.

Replacing the cover

Use this information to reinstall the cover.

To replace the server cover, complete the following steps:

Step 1.

Make sure that all cables, adapters, and other components are installed and seated correctly
and that you have not left loose tools or parts inside the server. Also, make sure that all internal
cables are correctly routed.

Before you slide the cover forward, make sure that all the tabs on the front, rear, and side of the
cover engage the chassis correctly. If all the tabs do not engage the chassis correctly, it will be
very difficult to remove the cover later.

Step 2.

Position the cover on top of the server.

Step 3.

Slide the cover toward the front of the server.

Step 4.

Make sure that the cover correctly engages all the inset tabs on the server.

Step 5.

Press down the blue latch on the top of the cover.

196

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands