manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 1053

3. Turn off the system and disconnect it from power. Wait for 45 seconds. Reseat DIMM(s).

Reconnect it to power.

4. Make sure that DSA and BIOS/uEFI are at the latest level.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

201-820-002 : Standalone Memory Test Aborted

Memory Upper limit is less than 16 Mbytes.

Recoverable

No

Severity

Warning

Serviceable

No

Automatically notify support

No

User Response

Complete the following steps:

1. Perform the actions mentioned one at a time and try the test after each action.

2. If the problem remains, contact your technical-service representative.

3. Turn off the system and disconnect it from power. Wait for 45 seconds. Reseat DIMM(s).

Reconnect it to power.

4. Make sure that DSA and BIOS/uEFI are at the latest level.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

201-820-003 : Standalone Memory Test Aborted

Memory Upper limit is less than 16 Mbytes.

Recoverable

No

Severity

Warning

Serviceable

No

Automatically notify support

No

Appendix C. DSA diagnostic test results

1041

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands